Epoxy.com Logo - Epoxy, Polyurethane, Polysulfide, Polyester, MMA - Methyl Methacrylate and other Construction Resin Systems - Over 350 Products- Since 1980
[Contact Us]

Medium Viscosity Methyl Methacrylate (MMA) Sealer and Top Coating

Epoxy.com Product #690

Ideal Sealer for Top Coating for MMA Flooring used in Food and Beverage Plants, Dairies,
or Other Wet Surfaces with Food and Fat Contamination


Description

Epoxy.com Product #690 Medium Viscosity Methyl Methacrylate (MMA) Sealer and Top Coating is a 100% reactive, medium viscosity methyl methacrylate resin developed as a sealer/topcoat over Epoxy.com Product #697 and Epoxy.com Product #698 Methyl Methacrylate (MMA) Flooring and Decking Systems.

Advantages

  • Fast Cure - Less than 1 hour
  • Suitable for USDA food handling areas
  • Higher Temperature Resistance
  • Superior Fat Resistance.
  • Medium Viscosity - excellent filling properties
  • Can be installed over a wide range of temperatures
  • 100% Reactive - VOC Compliant

Considerations

  • Concrete must be clean and free of all oil, grease, paint, dirt, sealers, laitance and any other foreign material that might interfere with proper bonding.
  • Do not store Epoxy.com Product #690 Medium Viscosity Methyl Methacrylate (MMA) Sealer in direct sunlight, storage temperature must be  less than 80 ° F.
  • On or below grade applications should have a moisture vapor barrier under the slab. Maximum vapor transmission must be less than 3 lbs per ASTM F-1869 and less than 80% RH per ASTM F-2170.
  • Maintain coating thickness at 10-20 mils (80-160 Square Feet per Gallon) to prevent yellowness and possible cracking.
  • Do not use over Epoxy.com Product #692 Flexible Methyl Methacrylate (MMA) Flooring.

Composition

Epoxy.com Product #690 Medium Viscosity Methyl Methacrylate (MMA) Sealer is a 100% Solids Methyl Methacrylate (MMA).

Surface Preparation

Good surface preparation is the first necessary step to successful installation of all Resinous Flooring System. All substrates must be clean and free of all oil, grease, paint, dirt sealers laitance and any other foreign matter that may interfere with proper bonding. Follow the directions for surface preparation as outlined in Epoxy.com Surface Preparation Guide.

Epoxy.com Epoxy Color Chart Here

Color Selection

Can be used clear (with a slight blue tint). Color packs are available in selected colors. Color pack mix ratio is 1 QT color pack per 5 gallon pail of Epoxy.com Product #690 Medium Viscosity Methyl Methacrylate (MMA) Sealer and Top Coating Resin.

Mixing and Installation

Epoxy.com Product #690 Low Viscosity Methyl Methacrylate (MMA) Sealer and Top Coating Resin requires the adding of Epoxy.com Product #695 Hardening Powder. to start the hardening process. The amount of hardener must be adjusted to the respective surface temperature (see table below). At temperatures below 40°F, Epoxy.com Product #696 Accelerator must be used, contact Epoxy.com Technical Support for a recommended dosing.

In order to achieve the best curing it is necessary to apply  Epoxy.com Product #699 Low Viscosity Methyl Methacrylate (MMA) Sealer with a short nap roller. Coating thickness should be a minimum of 10 mils and maximum of 20 mils (80-160 sq ft/gal.) depending on the profile of the base material. One hundred (100) sq ft/gal. is average. If the coating exceeds 20 mils, the top coat may remain visibly blue or yellow and surface cracks are possible. It is best to spread material with a notched trowel or squeegee to the desired thickness, and roll in one direction, then roll in a 90° pattern. This will reduce the occurrence of roller marks in the top coat.

Temp. (°F) of Resin, Air & Floor Surface

Hardener % by Wt. Based on Wt. of #699 Resin

Hardener by Vol. (oz.) Based on Gallon of #699 Resin

Pot Life (min.)

Hardness Time (min.)

+402.03.5Approx. 30Approx. 50
+501.52.7Approx. 25Approx. 40
+601.52.7Approx. 20Approx. 20
+701.01.8Approx. 10 Approx. 15

Epoxy.com recommends waiting 2 hours between coating and sealing. Coating work has to be continued after the complete hardening of the previous layer.

Physical Properties

Basic Material    Methyl Methacrylate Resin (MMA) 
Percent Reactive100%
Appearance  Clear Low Viscosity Liquid (with slight blue cast) 
Viscosity, cps@ 73°F     380-390
Weight per Gallon 8.3 lbs
Recoat Time 2 hours±
Pot Life Min
(Varies with Temp)
10-30
Cure Rate (min) 10-30
Heat Resistance 216°F
Shore D Hardness75-80

Cleanup

Clean tools and equipment with lacquer thinner or MEK. Consult Material Safety Data Sheet for safety and health precautions.

Coverage

100 square feet per gallon, average.

Availability

Contact Epoxy.com Customer Service Department

Maintenance

Epoxy.com Product #690 Low Viscosity Methyl Methacrylate (MMA) Sealer is considered to be a very low maintenance flooring system.  With some textures and conditions it may have to be cleaned by bristle brush or low pressure wash. Due to the thermoplastic character of Methyl Methacrylate (MMA) resins, you may get black marks from fork lifts and tire skidding.

Storage

Store Epoxy.com Product #690 Medium Viscosity Methyl Methacrylate (MMA) Sealer in a cool and dry place, below 80°F, out of direct sunlight. Do not store near open flame or food. Shelf life is 4-6 months in the original unopened containers.

Tips

Adequate cross ventilation should be provided. Good ventilation during the processing ensures a good cross linking and hardening. Read, understand and follow Material Safety Data Sheets and Application Instructions prior to use.

Use only as directed. If substrate and/or material temperature is above 90°F, DO NOT apply material.

Technical Support

Call Epoxy.com Technical Support Department with any technical support questions.

 

Proper mixing and installation is critical to the optimal success of all products.  See Installation Tips, Techdata, & MSDS for more details on our products.  Be sure to contact us with any questions and/or concerns that you have.

For more information please contact:

Epoxy.com
A Division of Epoxy Systems, Inc
A Vermont Corporation
USA

We have products that have passed the test of time as well as the best new Systems available today.

Since 1980 - 40 years of the highest quality products

Hours: 9AM-4PM Eastern Time (6AM-1PM Pacific Time)

Closed for lunch from 12Noon to 1PM


321-206-1833  Customer Service - Ordering and Order Status
                         Katey Lambert-Fontaine, VP - Chief Operations Officer
                         sales@epoxy.com

                        Technical Support
352-533-2167  Norm Lambert, President - Technical Support Director 
                         info@epoxy.com

352-489-1666  Accounting and Administration
                         Debby Lambert, CEO, and CFO

Copyright © 1994-2023 (providing online information about the right product for the right job for nearly 30 years)  EPOXY.COM a division of Epoxy Systems, Inc. - Florida and Vermont.  All rights reserved.

We accept MasterCard, Visa, American Express, Discover, Wire Transfers, and Cashiers Checks
We accept MasterCard, Visa, American Express, Discover, or Wire Transfers.